Gladhand

CDL basics · Inspection

CDL pre-trip inspection: the seven steps, the DVIR and what the test asks

Last updated · Published by Certloom Learning

How this page was made: Drafted with AI assistance by Certloom Learning from the official sources listed at the end, read on 2026-11-12 (news coverage is named where an official page blocked automated access). Practice questions come from Gladhand's AI-reviewed question bank. Not reviewed by a licensed CDL instructor or a lawyer.

A pre-trip inspection is a check you do before driving to find problems that could cause a crash or a breakdown. The CDL manual teaches it as seven steps: vehicle overview, engine compartment, start the engine and check the cab, check the lights, walk around and check the vehicle, check the signal lights, and check the brakes. Federal rules also require a driver to be satisfied the vehicle is in safe operating condition before driving (49 CFR 396.13 (checked 2026-11-12)), and to prepare a written report at the end of each day's work on each vehicle (49 CFR 396.11 (checked 2026-11-12)).

What are the seven steps of a pre-trip inspection?

The step numbers below come from Gladhand's reviewed questions, written from the Commercial Driver Handbook:

StepWhat you do
1. Vehicle overviewLook at the vehicle as you walk up. Check the last inspection report and look under the vehicle for fresh oil, coolant, grease or fuel leaks.
2. Engine compartmentMake sure the parking brake is on and/or the wheels are chocked, then check fluids, belts and hoses.
3. Start the engine, check the cabPut a manual gearshift in neutral before starting. Oil pressure should come up to normal within seconds, and the ABS light should come on and then go out.
4. LightsTurn on the low beams and the four-way flashers, turn off the engine, take the key with you and check the front lights.
5. WalkaroundCheck the tires, wheels, suspension, brakes, coupling and lights. Clearance lights and reflectors at the front are amber.
6. Signal lightsCheck the turn signals and stop lights. To turn on the stop lights, apply the trailer hand brake or have a helper press the pedal.
7. BrakesTest the parking brake by letting the vehicle move forward slowly and applying it, and test the service brake at about 5 mph.

What does the DVIR have to cover?

The driver vehicle inspection report is written at the end of each day's work on each vehicle operated. It must cover at least service brakes, parking brake, steering, lighting devices and reflectors, tires, horn, windshield wipers, mirrors, coupling devices, wheels and rims, and emergency equipment (49 CFR 396.11(a) (checked 2026-11-12)). The driver does not have to prepare one if no defect was found or reported. The carrier must keep the report and repair certification for three months.

“Before driving a motor vehicle, the driver shall: (a) Be satisfied that the motor vehicle is in safe operating condition”

Official text: 49 CFR 396.13(a) (checked 2026-11-12)

Why does it matter in English?

Officers may ask about your equipment and inspections in English during a stop; see the brake and light check instructions. The test is a good place to learn the English parts names too: tires, wheels, rims, brakes, steering, suspension, exhaust, coupling.

Can you answer these practice questions?

6 sample questions from Gladhand's reviewed bank of 1,792. Open each one to check your answer.

  1. In the seven-step pre-trip inspection method, what is step 1?

    1. Vehicle overview
    2. Check the signal lights
    3. Start the engine and test the brakes
    4. Do the walkaround inspection
    Show answer

    Answer: A. Step 1 is the vehicle overview: approach the vehicle, notice its general condition, look for leaks and hazards, and review the last inspection report.

    El paso 1 es la vista general del vehículo: acercarse, ver su condición general, buscar fugas y peligros, y revisar el último reporte de inspección.

    California Commercial Driver Handbook §11 · gk01-036

  2. Under 49 CFR 396.11, when is the written driver vehicle inspection report (DVIR) prepared?

    1. Only when the vehicle is due for an oil change
    2. At the end of each day's work on each vehicle operated
    3. At the start of each week
    4. Only after a roadside inspection
    Show answer

    Answer: B. The DVIR is prepared at the end of each day's work for each vehicle the driver operated. It lists any defects that would affect safety or cause a breakdown.

    El DVIR se prepara al final de cada día de trabajo para cada vehículo que el chofer operó. Enumera los defectos que afectarían la seguridad o causarían una descompostura.

    49 CFR 396.11 · gk01-053

  3. Under 49 CFR 396.13, what must a driver do before driving a commercial motor vehicle?

    1. Wash the vehicle and clean all windows
    2. Call the carrier to ask for permission to take the vehicle out
    3. Drive around the yard for at least 10 minutes to warm up the brakes
    4. Be satisfied that the vehicle is in safe operating condition
    Show answer

    Answer: D. Before driving, the driver must be satisfied that the vehicle is in safe operating condition. The driver also reviews the last DVIR when one is required.

    Antes de manejar, el chofer debe estar seguro de que el vehículo está en condiciones seguras de operación. También revisa el último DVIR cuando se requiere uno.

    49 CFR 396.13 · gk01-059

  4. While driving, you smell something burning and hear a new noise. What should you do?

    1. Turn up the radio so the noise is not a distraction
    2. Check it as soon as you can safely stop
    3. Drive faster to reach a repair shop sooner
    4. Keep driving and report it after the trip
    Show answer

    Answer: B. During a trip, use your senses: look, listen, smell, and feel. If something might mean trouble, check it when you can safely stop.

    Durante el viaje, use sus sentidos: mirar, escuchar, oler y sentir. Si algo puede indicar un problema, revíselo cuando pueda detenerse con seguridad.

    California Commercial Driver Handbook §2.1 · gk01-005

  5. When should you do an after-trip (post-trip) inspection?

    1. Only once a month on each vehicle, when it goes in for scheduled service
    2. At the end of the trip, day, or tour of duty on each vehicle you drove
    3. Only at the start of the next shift, before the next driver takes the vehicle
    4. Only when a mechanic asks you to
    Show answer

    Answer: B. Do an after-trip inspection at the end of each trip, day, or tour of duty on every vehicle you operated.

    Haga una inspección después del viaje al final de cada viaje, día o turno, en cada vehículo que operó.

    California Commercial Driver Handbook §2.1 · gk01-009

  6. What is the most important reason to inspect your vehicle?

    1. To keep the truck looking clean
    2. Safety for you and other road users
    3. To use time while you wait for a load
    4. To lower your fuel costs
    Show answer

    Answer: B. Safety is the most important reason to inspect. An inspection finds problems that could cause a crash or a breakdown before you drive.

    La seguridad es la razón más importante para inspeccionar. La inspección encuentra problemas que pueden causar un choque o una descompostura antes de manejar.

    California Commercial Driver Handbook §2.1 · gk01-001

The Gladhand app has the full bank, Spanish help you can turn off, and the roadside stop simulator.

What else do drivers ask?

Is the pre-trip inspection part of the CDL test?
Yes. The skills test includes a vehicle inspection, and the knowledge test has questions about it. Your state’s manual and test center describe the details.
Who signs the DVIR?
The driver who prepared it signs it. The next driver signs only when defects were noted and certified as repaired or not needing repair (49 CFR 396.13(c)).

Where does this information come from?

These are the official sources behind the facts on this page, with the date we checked each one.

What should you study next?

General study information, not legal advice. Rules change and some differ by state, so confirm with your state licensing agency and FMCSA.