Gladhand

CDL knowledge test · Air brakes

CDL air brakes test: what it covers and the numbers to know

Last updated · Published by Certloom Learning

How this page was made: Drafted with AI assistance by Certloom Learning from the official sources listed at the end, read on 2026-11-11 (or confirmed in named news coverage where the official page blocked automated access). Practice questions come from Gladhand's AI-reviewed question bank. Not reviewed by a licensed CDL instructor or a lawyer.

The CDL air brakes test is a separate knowledge test, taken with general knowledge, on section 5 of your state CDL manual: the parts of the system, dual air systems, inspecting the brakes, braking technique and parking. You need at least 80 percent to pass (49 CFR 383.135 (checked 2026-11-11)). Fail it, or take the skills test in a vehicle without air brakes, and your CDL gets a restriction that keeps you out of air brake vehicles (49 CFR 383.95 (checked 2026-11-11)).

“If an applicant either fails the air brake component of the knowledge test, or performs the skills test in a vehicle not equipped with air brakes, the State must indicate on the CLP or CDL, if issued, that the person is restricted from operating a CMV equipped with any type of air brakes.”

Official text: 49 CFR 383.95(a)(1) (checked 2026-11-11)

What does the CDL air brakes test cover?

Five areas, all from section 5 of the state manual (Pennsylvania PUB 223, section 5 (checked 2026-11-11)):

Which psi numbers do you need to know for the air brakes test?

Governor cut-out at about 125 psi and cut-in at about 100 psi, the low air warning before 60 psi, spring brakes between 20 and 45 psi, and build-up from 85 to 100 psi within 45 seconds. These figures are in section 5 of state CDL manuals built on the national model; we checked them in Pennsylvania's manual (PUB 223) (checked 2026-11-11), and the Texas handbook Gladhand questions cite uses the same numbers. Your vehicle's manufacturer specifications can differ, and the manuals say so.

CheckNumber in the CDL manual
Governor cut-out (compressor stops pumping)about 125 psi
Governor cut-in (compressor starts again)about 100 psi
Safety valve opensabout 150 psi
Low air pressure warning comes onbefore pressure falls below 60 psi
Spring brakes come on (and tractor protection valve closes)between 20 and 45 psi
Air build-up, dual air system, at operating rpm85 to 100 psi within 45 seconds
Leakage, brakes released, engine offunder 2 psi in one minute (single vehicle), 3 psi (combination)
Leakage, brakes applied with 90 psi or moreunder 3 psi in one minute (single vehicle), 4 psi (combination)

How do you do the air brake check in the vehicle inspection?

For air brake vehicles the manual replaces the hydraulic brake check in the walkaround with these checks, in this order:

  1. Leakage rate. Fully charged system, engine off, parking brake released: time the drop for one minute. Then hold the pedal at 90 psi or more and time it again.
  2. Low pressure warning. Fan the pedal to lower the pressure. The warning must come on before 60 psi.
  3. Spring brakes come on automatically. Keep fanning: the parking brake valve (and the tractor protection valve on a tractor-trailer) should pop out at the manufacturer's setting.
  4. Build-up rate. At operating rpm, 85 to 100 psi within 45 seconds on a dual air system.
  5. Governor cut-in and cut-out. Pumping should start around 100 psi and stop around 125 psi.
  6. Parking brake and service brake tests at low speed.

Your state's skills test may ask you to explain each step in English while you do it. Practicing the words matters as much as the numbers.

Can you answer these practice questions?

8 sample questions from Gladhand's reviewed bank of 1,792. Open each one to check your answer.

  1. At about what pressure should the air compressor governor 'cut out' and stop the compressor from pumping air?

    1. 150 psi
    2. 100 psi
    3. 60 psi
    4. 125 psi
    Show answer

    Answer: D. The governor should cut out at about 125 psi. It cuts back in at about 100 psi, and 150 psi is where the safety valve usually opens.

    El gobernador debe cortar a unos 125 psi. Vuelve a activar el compresor (cut-in) a unos 100 psi, y 150 psi es donde normalmente se abre la válvula de seguridad.

    Texas CDL Manual (DPS DL-7C) §5.3 · air03-060

  2. On most vehicles, the low air pressure warning must come on before tank pressure falls below:

    1. 60 psi
    2. 45 psi
    3. 20 psi
    4. 100 psi
    Show answer

    Answer: A. The low air pressure warning comes on before air pressure in the tanks falls below 60 psi. The 20 to 45 psi range is where the spring brakes come on.

    La advertencia de baja presión de aire se prende antes de que la presión en los tanques baje de 60 psi. El rango de 20 a 45 psi es donde se aplican los frenos de resorte (spring brakes).

    Texas CDL Manual (DPS DL-7C) §5.1 · air03-045

  3. As air pressure leaks away, in what pressure range will the spring brakes come on?

    1. 5 to 10 psi
    2. 20 to 45 psi
    3. 60 to 80 psi
    4. 100 to 125 psi
    Show answer

    Answer: B. The spring brakes come on when air pressure drops into the range of 20 to 45 psi. The low air warning comes on earlier, before pressure falls below 60 psi.

    Los frenos de resorte se aplican cuando la presión baja al rango de 20 a 45 psi. La advertencia de baja presión se prende antes, antes de que baje de 60 psi.

    Texas CDL Manual (DPS DL-7C) §5.4 · air03-042

  4. In a dual air system, with the engine at operating rpm, the air pressure should build from 85 to 100 psi within:

    1. 2 minutes
    2. 45 seconds
    3. 10 seconds
    4. 3 minutes
    Show answer

    Answer: B. In dual air systems, pressure should build from 85 to 100 psi within 45 seconds at operating rpm. The 3-minute figure is for older single air systems.

    En los sistemas dobles de aire, la presión debe subir de 85 a 100 psi en 45 segundos a revoluciones de operación. Los 3 minutos son para los sistemas de aire sencillos más viejos.

    Texas CDL Manual (DPS DL-7C) §5.3 · air02-037

  5. You test a combination vehicle with the engine off and the brakes released. What air loss in one minute means there is too much leakage?

    1. More than 10 psi
    2. More than 3 psi
    3. More than 2 psi
    4. More than 4 psi
    Show answer

    Answer: B. With the brakes released, a combination vehicle should not lose more than 3 psi in one minute. The 2 psi limit is for single vehicles, and 4 psi is for a combination with the brakes applied.

    Con los frenos sueltos, un vehículo de combinación no debe perder más de 3 psi en un minuto. El límite de 2 psi es para vehículos sencillos, y el de 4 psi es para combinaciones con los frenos aplicados.

    Texas CDL Manual (DPS DL-7C) §5.3 · air03-058

  6. Why do the air tanks need to be drained?

    1. Draining keeps the ABS wheel sensors working correctly
    2. Draining resets the governor to the right cut-out pressure
    3. Water and compressor oil collect in the bottom of the tanks
    4. Old air loses its pressure if it stays in the tanks
    Show answer

    Answer: C. Compressed air usually has some water and compressor oil in it, which is bad for the air brake system. They collect in the bottom of the tanks, so drain the tanks completely.

    El aire comprimido casi siempre trae algo de agua y aceite del compresor, y eso es malo para los frenos de aire. Se juntan en el fondo de los tanques, así que púrguelos por completo.

    Texas CDL Manual (DPS DL-7C) §5.1 · air03-055

  7. What is a dual air brake system?

    1. One air system that works the brakes on the trailer only
    2. Two separate air brake systems that share one set of brake controls
    3. A system with two brake pedals, one for each driver
    4. An air brake system that is backed up by a separate hydraulic brake system
    Show answer

    Answer: B. A dual air brake system has two separate air systems, but the driver uses a single set of brake controls. Most heavy-duty vehicles use this design.

    Un sistema doble de frenos de aire tiene dos sistemas de aire separados, pero el chofer usa un solo juego de controles de freno. La mayoría de los vehículos pesados usan este diseño.

    Texas CDL Manual (DPS DL-7C) §5.2 · air02-001

  8. What is the first step of the 'stab braking' method?

    1. Apply the brakes all the way
    2. Apply the brakes just enough to feel a slowdown
    3. Apply the brakes hard but stop before the wheels lock
    4. Shift to neutral, then apply the brakes lightly
    Show answer

    Answer: A. In stab braking, you apply the brakes all the way, release them when the wheels lock, and apply them fully again when the wheels roll. Braking hard without lockup is controlled braking.

    En el frenado intermitente, aplica los frenos a fondo, los suelta cuando las ruedas se bloquean y los vuelve a aplicar a fondo cuando las ruedas giran. Frenar fuerte sin bloquear es el frenado controlado.

    Texas CDL Manual (DPS DL-7C) §5.4 · air03-017

The Gladhand app has the full bank, Spanish help you can turn off, and the roadside stop simulator.

What else do drivers ask?

How many questions are on the air brakes test?
It depends on the state, so check your state manual or licensing agency. Federal rules require a score of at least 80 percent on each knowledge test (49 CFR 383.135).
What is the L restriction?
If you do not pass the air brakes knowledge test, or you take the skills test in a vehicle without air brakes, your CDL gets the L restriction: no commercial vehicle with any type of air brakes.

Where does this information come from?

These are the official sources behind the facts on this page, with the date we checked each one.

What should you study next?

General study information, not legal advice. Rules change and some differ by state, so confirm with your state licensing agency and FMCSA.